Looking for:
X-micro wlan 11g pcmcia card driver download. X-Micro XWL-11GPAG Manuals |
X-micro wlan 11g pcmcia card driver download -
X-micro wlan 11g pcmcia card driver download.X-Micro WLAN 11g Turbo Mode Broadband Router and PCMCIA card
The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments for example:. On board of airplanes, or In an explosive environment, or In case the interference risk to other devices or services is perceived or identified as harmful In case the policy regarding the use of Wireless LAN devices in specific organizations or environments e.
Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. The Manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, of the substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines.
Operation is subject to the following two conditions:. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of this device.
Nevertheless, this device shall be used in such a manner that the potential for human contact during normal operation is minimized. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:.
Reorient or relocate the receiving antenna. Increase the distance between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Export restrictions This product or software contains encryption code that may not be exported or transferred from the US of Canada without an approved US Department of Commerce export license. Safety Information Your device contains a low power transmitter. When device is transmitted it sends out radio frequency RF signal.
Use on the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Protection requirements for health and safety Article 3. These are considered relevant and sufficient. Protection requirements for electromagnetic compatibility Article 3. Effective use of the radio spectrum Article 3. CE in which Countries where the product may be used freely:.
France: except the channel 10 through 13, law prohibits the use of other channels. This manual contains detailed instructions in operation of this product. Please keep this manual for future reference. Wireless PCMCIA Card can wirelessly transmit and receive data, minimizing the need for wired connections, at a speed of up to fifty-four megabit per second.
The mobility provides productivity and service, which are not available under wired networks. The Wireless PCMCIA Card configuration is easy to change from peer-to-peer networks, suitable for a small number of users, to full infrastructure networks of thousands of users that allow roaming around a broad area.
Overview of this Users Guide Introduction. Unpacking and Setup. Hardware Installation. Describes the LED indicators of the Adapter. Software Installation. Tells how to setup the driver and the utility setting. Technical Specifications. The box should contain the following items:. Otherwise the indicator is off whiles the Wireless LAN is stand by. The Install Shield Wizard screen will appear. Click Next to continue. The installation program will help you to setup the Wireless Cardbus utility.
When the icon in the toolbar represents in full green color then the signal strength has an excellent performance with the AP, if it represents in yellow color then the signal strength has a fair performance with the AP, and if the icon represents no color, then the signal strength has a worst performance with the wireless station.
Link Information The default page is as below after launching the Utility program. Frequency: Shows the current frequency used for wireless network. Wireless Mode: Shows the current wireless mode used for wireless communication. Encryption: Shows the current encryption mode used for wireless network. TxRate: Shows the current data rate used for transmitting.
Channel: Shows the current channel for communication. Data Rate: Shows the statistics of data transfer, and the calculation is based on the number of packets transmitted and received. Configuration This is the page where changes the basic settings of the PC card with the minimum amount of effort to implement a secure wireless network environment. The SSID must be identical for each clients and nodes in the wireless network. Wireless Mode: There are two types available for selection.
Infrastructure to establish wireless communication with LAN and other wireless clients through the use the Access Points. Ad-Hoc to establish point-to-point wireless communication directly with other wireless client devices such as wireless network PCI Adapter.
Tx Rate: Select the data rate for data transmission. Power Mode: There are 3 modes to choose. Continuous Access Mode default the PC card is constantly operating with full power and it consumes the most power. Maximum Power Save the PC card consumes the least power and only operates when there is wireless network activity.
Power Save the PC card consumes the moderate level of power. Preamble is a sequence of bits transmitted at 1Mbps that allows the PHY circuitry to reach steady-state demodulation and synchronization of bit clock and frame start. At the receiver, the Preamble and header are processed to aid in demodulation and delivery of the PSDU. The Short Preamble and header may be used to minimize overhead and, thus, maximize the network data throughput.
That means that stations using Short-Preamble cannot communicate with stations implementing the original version of the protocol. Click Apply for the changes to take effect. The default setting is 11B, 11G and eXtended Range enable, which is interoperable with both 11B and 11G devices, and provide more than m connection ability. Note: user must select one of 11B or 11G at least, otherwise the wireless connection will not function. If one of the two 7 options is selected, it is required to select the Authentication mode from the next dropping list.
If WPA is selected, configuration is enabled. Please click the configuration. The below window is pop up. Then, please select the certificate that user wants to use and enter the server name and login name If WPA-PSK is selected, click the configuration button. The popping window is as the below.
Please enter the key. Mode: There are three modes available to choose. Open Authentication the sender and receiver do not share secret Key for communication. Instead, each party generates its own key-pairs and asks the other party to accept it.
The key is regenerated when the connection is established every time. Shared Authentication the sender and receiver shares the common key for data communication, and the key is used for extended length of time. Auto depend on the communication to establish, and automatically use the proper authentication mode. The following will only be activated to allow for configuration when Encryption is enabled. Default Key: select one of the 4 keys to use.
Site Survey This page allows user to enable the Site Survey function to scan for the available wireless network wireless clients and Access Points and establish wireless communications with one. Available Network displays the wireless networks wireless clients and Access Points that are in signal range. Select any one of them to establish communications by simply mouse double-click or click on the Connect button. Click Refresh button to start scanning for available network again.
Profile User can create and manage the created profiles for Home, offices or public areas. By double-clicking on one of the created profile, the setting will adapt to the configuration such as SSID, channel, and WEP settings saved by that particular profile.
Remove: To remove the selected the profile Properties: To view and change its settings of the profile. Then, the following screen would appear. User can enter the necessary information required for accessing Access Points or Wireless Router.
When there is new version of software available for upgrade, users will be able to identify by version numbers. Application Forms.
No comments:
Post a Comment